ThinSHUFFLE™ Flex Circuit MPO Shuffle Assemblies

Mesh MPO shuffle routed on a thin, flexible substrate. 4x4 on MPO-8 or 8x8 on MPO-16, with machine-placed routing and colour-identified upstream legs for each switch fabric.
  • 4x4 or 8x8 mesh shuffle, every MPO port reaches every fabric
  • Fibres bonded to a thin, flexible substrate under conformal coating
  • Machine-placed routing for a repeatable lane map and controlled bend radius
  • Fits cassettes, chassis, sleds and backplanes where a shuffle box will not
  • Upstream legs colour coded per fabric in TIA-598 order
  • Factory terminated and 100% IL/RL tested

Engineered to Outperform

Delivered with Certainty

Procurement Made Simple

Rapid Deployment Ready

Ready To Scale

Compliance Assured

ThinSHUFFLE™ flex circuit MPO shuffle assemblies route every fibre of a mesh shuffle on a thin, flexible substrate. Individual fibres are laid down and bonded to the film by machine, then sealed under a conformal coating, so the full cross-connect between input and output MPO legs is fixed in a single flat circuit rather than in a moulded box or a bundle of loose fibres.

Because the routing is placed by machine, every assembly carries the same lane map with no hand-routing errors, and the fibres hold their position and bend radius in service. The substrate is only a few hundred microns thick and can be flexed, folded or mounted through its corner holes, so it fits inside cassettes, switch chassis, sleds and backplanes where a conventional shuffle box will not.

Standard configurations include 4x4 on MPO-8 (32 fibre) and 8x8 on MPO-16 (128 fibre), for 400G, 800G and 1.6T leaf-spine and AI cluster fabrics.

Assemblies use bend-insensitive single-mode G.657.A1 fibre with ScaleFibre Low Loss MPO connectors, and are factory terminated and 100% tested for insertion loss and return loss before shipment. Custom lane maps, port counts and substrate outlines are available on request.

Intended for leaf-spine and AI cluster fabrics across the Sydney and Melbourne metropolitan data centre clusters, meshing four or eight upstream switch fabrics on a thin flexible circuit with colour-identified legs.
General
Configuration4x4 mesh shuffle (4 × MPO-8 each side), 8x8 mesh shuffle (8 × MPO-16 each side), or Base-8 to Base-12 conversion (3 × MPO-8 to 2 × MPO-12). Other port counts custom-routed on request
Fibre Count32 fibres (4x4, MPO-8), 128 fibres (8x8, MPO-16) or 24 fibres (3 × MPO-8 to 2 × MPO-12)
Lane MappingMesh, duplex: each leg distributes its duplex lanes across all legs on the opposite side. Custom lane maps available on request
Leg IdentificationUpstream legs colour coded in TIA-598 order: blue, orange, green and brown (4x4); blue, orange, green, brown, slate, white, red and black (8x8)
FormatFlexible optical circuit with corner mounting holes, for mounting in cassettes, chassis, sleds or backplanes
Technical Specs
SubstrateFlexible film, fibres sealed under conformal coating
Fibre RoutingMachine-placed, single layer, controlled minimum bend radius
Fibre TypeSingle-mode G.657.A1
ConnectorsMPO-8, MPO-12 or MPO-16, Female or Male, APC polish
Connector Polish Angle8° APC (Angled Physical Contact)
Insertion Loss≤0.35 dB per MPO connector
Return Loss≥60 dB
Operating Temperature-20°C to +70°C
ComplianceRoHS, REACH
Single-mode (G.657.A1), 4x4 Mesh Duplex
FC-S7-32-4MP8F-MDFlexible optic circuit, Single Mode (G.657.A1), 32 fibre, 4 x MPO-8 female each end, mesh (any-to-any), duplex
Single-mode (G.657.A1), 8x8 Mesh Duplex
FC-S7-128-8MP16F-MDFlexible optic circuit, Single Mode (G.657.A1), 128 fibre, 8 x MPO-16 female each end, mesh (any-to-any), duplex
Single-mode (G.657.A1), Base-8 to Base-12 Conversion
FC-S7-24-3MP8F-2MPOF-BFlexible optic circuit, Single Mode (G.657.A1), 24 fibre, 3 x MPO-8 female to 2 x MPO-12 female, Base-8 to Base-12 conversion